Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

NANAIU

Well-known Member
Joined
Oct 15, 2010
Age
34
Posts
2,734
Likes
63
Location
BD
Let's post all logs in this thread.

C902 Flashing Logs:

Code:
4SE - tool 1.8.1
Selected model: C902
Selected operation: Flash
Selected interface: USB (BOOTROM)
Checking USB driver status...OK (SEMC Flash Device v2.2.0.5 | 5-4-2010)
Remove battery, wait a few seconds and insert it back
Plug USB cable holding both "2" and "5" buttons
Connected to USB4
You can now release the keys and allow the process to run. Do not disconnect the phone
Device identification...OK
        Sending Preloader...OK
        Sending IDloader...OK
        Chip:DB3150 Model:C902 IMEI:35362603-791853-4 CID:52 Domain:RED
        OTP LOCKED:1 CID:52 PAF:1
Uploading logic DB3150:
        Detecting flash type...OK
                ID: 2CAA (Micron)
                Chip: Micron 2048 Mbit NAND (large page) x08
                Logical address: 0x80000000
                Size: 264 Mb
        Reading TA security data...OK
        Sending CSLoader...OK
C902 CID52 RedBrownBlue (R3EG004AS | 1208-6209) CUSTOMIZED UK/SWIFT BLACK
Flashing 276661140_0124A5A35FF0.SOFTWARE (816 blocks)...OK
Flashing 276728364_0124A5986370.SOFTWARE (704 blocks)...OK
        Starting filesystem service...OK
Uploading 276184620_012475E0F700.FILE_SET (16 files)...OK
Shutting down device...OK
Operation completed successfully. You can disconnect the phone now
FINISHED [309sec]
... more to come!!
 

NANAIU

Well-known Member
Joined
Oct 15, 2010
Age
34
Posts
2,734
Likes
63
Location
BD
answer: Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

U5i Vivaz

Read Info Logs:

Read TA Logs:

Code:
4SE - tool 1.8.1
Selected model: Vivaz™ (U5)
Selected operation: TA
Selected interface: USB (EROM)
Checking USB driver status...OK (SEMC Flash Device v2.2.0.5 | 5-4-2010)
Remove battery, wait a few seconds and insert it back
Plug USB cable holding "Green" button
Connected to USB1
You can now release the keys and allow the process to run. Do not disconnect the phone
Device identification...OK
        Chip:OMAP3430 Model:U5i IMEI:35938703-703061-4 AID:0002 Color:RED
        DEVICE_ID: F6BD4AE20F799E119E9C42FF5741082131F1FE1C
        EROM: 1217-2350 R8A017
Uploading logic OMAP3430:
        Sending LoaderLIVE...OK
        Detecting flash type...OK
                ID: EC40 (Samsung)
                Chip: Samsung OneNAND 2048 Mbit NAND (small page)
                Logical address: 0x00000000
                Size: 264 Mb
        OTP: LOCKED
        Reading TA security data...OK
Reading entire TA...OK
Reading entire TA misc...OK
Device data saved to: C:\Documents and Settings\Administrator\My Documents\U5.zip
Shutting down device...OK
Operation completed successfully. You can disconnect the phone now
FINISHED [13sec]
BR
 

NANAIU

Well-known Member
Joined
Oct 15, 2010
Age
34
Posts
2,734
Likes
63
Location
BD
answer: Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

X10 UNLOCK SUCCESSFULLY noTP\no CREDITS

X10 UNLOCK SUCCESSFULLY noTP\no CREDITS, THX TO 4SE TEAM.
 

NANAIU

Well-known Member
Joined
Oct 15, 2010
Age
34
Posts
2,734
Likes
63
Location
BD
answer: Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

SUCCESFULLY FLASHED E-15i experia 4SE - tool 1.8.2
Selected model: Xperia™ X8 (E15)
Selected operation: Flash
Selected interface: USB (EROM)
Checking USB driver status...OK (SEMC Flash Device v2.2.0.5 | 1-29-2010)
Remove battery, wait a few seconds and insert it back
Plug USB cable holding "Back" button
Connected to USB7
You can now release the keys and allow the process to run. Do not disconnect the phone
Device identification...OK
Chip:MSM7227 Model:E15i IMEI:01244800-466125-9 AID:0001 Color:RED
DEVICE_ID: FC1B863E04777FB18BFA49A58A6A401D0CCFD1C9
EROM: 1229-3593 R8A029
Uploading logic MSM7227:
Sending LoaderLIVE...OK
Detecting flash type...OK
ID: 20BC (ST)
Chip: ST 4096 Mbit NAND (large page)
Logical address: 0x08000000
Size: 528 Mb
OTP: LOCKED
Reading TA security data...OK
E15A 0001 Red (2.1.1.A.0.6 | 1242-1266/R1B) CUSTOMIZED GEL (GENERIC LAM)/DARK BLUE/WHITE
Processing 277563214_012DC80C5AE8.SIN_FILE_SET...
Flashing image fota0_S1-SW-LIVE-3EDC-0001-S1-PARTITION.sin...OK
Flashing image fota1_S1-SW-LIVE-3EDC-0001-S1-PARTITION.sin...OK
Flashing image kernel_S1-SW-LIVE-3EDC-0001-S1-PARTITION.sin...OK
Flashing image amss_S1-SW-LIVE-3EDC-0001-S1-PARTITION.sin...OK
Flashing image cache_S1-SW-LIVE-3EDC-0001-S1-PARTITION-WITH-SPARE.sin...OK
Processing 277601765_012F782D37C0.SIN_FILE_SET...
Flashing image amss_fs_shakira_BC125_S1-SW-LIVE-3EDC-0001-S1-PARTITION.sin...OK
Flashing image userdata_S1-SW-LIVE-3EDC-0001-S1-PARTITION-WITH-SPARE.sin...OK
Flashing image system_S1-SW-LIVE-3EDC-0001-S1-PARTITION-WITH-SPARE.sin...OK
Shutting down device...OK
Operation completed successfully. You can disconnect the phone now
FINISHED [143sec]
 

NANAIU

Well-known Member
Joined
Oct 15, 2010
Age
34
Posts
2,734
Likes
63
Location
BD
answer: Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

UNLOCK SUCESSFULLY EXPERIA E-15i AFTER UPDATE 4SE - tool 1.8.2
Selected model: Xperia™ X8 (E15)
Selected operation: Unlock
Selected interface: USB (EROM)
Checking USB driver status...OK (SEMC Flash Device v2.2.0.5 | 1-29-2010)
Checking ADB drivers status...OK
Remove battery, wait a few seconds and insert it back
Plug USB cable holding "Back" button
Connected to USB8
You can now release the keys and allow the process to run. Do not disconnect the phone
Device identification...OK
Chip:MSM7227 Model:E15a IMEI:01244800-466125-9 AID:0001 Color:RED
DEVICE_ID: FC1B863E04777FB18BFA49A58A6A401D0CCFD1C9
EROM: 1229-3593 R8A029
Uploading logic MSM7227:
Sending LoaderLIVE...OK
Detecting flash type...OK
ID: 20BC (ST)
Chip: ST 4096 Mbit NAND (large page)
Logical address: 0x08000000
Size: 528 Mb
OTP: LOCKED
Reading TA security data...OK
Opening TA...OK
Reading SIMLock data...OK
Original HwConf certificate detected
Processing SIMLock signature...OK
Opening TA...OK
Writing SIMLock data...OK
Disconnect USB cable, power on the phone and boot Android OS
Enable USB Debug in Applications menu, make sure ADB drivers installed. Connect USB cable
Starting ADB server...OK
Waiting for CB511PB65C...OK
Disabling security...OK
Waiting for CB511PB65C...OK
Removing NAND restrictions...OK
Waiting for CB511PB65C...OK
Disabling security...OK
Waiting for CB511PB65C...OK
Installing required module...OK
Writing S1boot image...OK
Rebooting device...OK
Operation completed successfully. You can disconnect the phone now
FINISHED [202sec]
 

NANAIU

Well-known Member
Joined
Oct 15, 2010
Age
34
Posts
2,734
Likes
63
Location
BD
answer: Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

SE j105 flash successfully
 

NANAIU

Well-known Member
Joined
Oct 15, 2010
Age
34
Posts
2,734
Likes
63
Location
BD
answer: Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

WT19 Walkman Live Unlocked !! 4SE - tool 1.8.2
Wybrany model: Live with Walkman (WT19)
Wybrana operacja: Odblokowanie
Wybrany interfejs: USB (BOOTROM)
Sprawdzanie sterowników USB...Błąd (Brakuje rekordu urządzenia)
Wyciągnij baterię. Podłacz TP do masy i podłacz kabel USB
Podłaczony przez USB3
Możesz teraz puścić przyciski. Nie odłączaj telefonu.
Identyfikacja telelfonu
Łączenie DLOAD....OK (PBL_DownloaderVER1.0)
Wysyłanie Preloader...OK
Podłaczony przez USB3
Wysyłanie LoaderTEST...OK
Chip:QC8255 Model:WT19i IMEI:35850804-xxxxxx-7 AID:0001 Kolor:BROWN
DEVICE_ID: 0474D73AFC7D61CCDAF6BEDA2E9748169B0276AB
Wgrywanie QC8255:
Wykrywanie typu flashaOK
ID: 98B3 (Toshiba)
Chip: Toshiba 8192 Mbit NAND (large page) x16
Adres logiczny: 0x00000000
Rozmiar: 1056 Mb
Rozmiar bloku logicznego: 0x40000
Liczba bloków logicznych:0x1000
OTP: LOCKED
Odczyt obszaru zabezpieczeń TA...OK
Otwieranie TA...OK
Odczyt danych SIMLockOK
Oryginalny certyfikat HwConf rozpoznany
Przetwarzanie danych SIMLockOK
Otwieranie TA...OK
Zapis danych SIMLock...OK
Wgrywanie obrazu S1boot....OK
Odłaczanie telefonuOK
Operacja zakończona pomyślnie. Możesz odłaczyć telefon.
Zakończono [42sec]
 

NANAIU

Well-known Member
Joined
Oct 15, 2010
Age
34
Posts
2,734
Likes
63
Location
BD
answer: Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

E10i successfull unlock

 

NANAIU

Well-known Member
Joined
Oct 15, 2010
Age
34
Posts
2,734
Likes
63
Location
BD
answer: Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

4SE - tool 1.8.2
Selected model: Xperia™ X8 (E15)
Selected operation: Read info
Selected interface: USB (EROM)
Checking USB driver status...OK (SEMC Flash Device v2.2.0.5 | 5-4-2010)
Remove battery, wait a few seconds and insert it back
Plug USB cable holding "Back" button
Connected to USB3
You can now release the keys and allow the process to run. Do not disconnect the phone
Device identification...OK
Chip:MSM7227 Model:E15i IMEI:35678504-012722-3 AID:0001 Color:RED
DEVICE_ID: 86445C8FDFB3D6E39052F50363B0549CE002C3CC
EROM: 1229-3593 R8A029
Uploading logic MSM7227:
Firmware details:
Software Id: 1236-9291
Software revision: 2.1.1.A.0.6
FS Id: HUTCH-1-8
FS version: 2.1.1.A.0.6
CDA Id: 1241-4648
CDA version: R6B
Sending LoaderLIVE...OK
Detecting flash type...OK
ID: 20BC (ST)
Chip: ST 4096 Mbit NAND (large page)
Logical address: 0x08000000
Size: 528 Mb
OTP: LOCKED
LoaderAID:0001 EROMAID:0001 SWAID:0001 CustAID:0001 SIMLockAID:0001 HWConfAID:0001
FUSES(0-3): 00774DFD 00040447 2004080F 7024E4C5
Reading TA security data...OK
Supported operations:
Flash, Unlock, Recovery, TA, Dump flash
Shutting down device...OK
Operation completed successfully. You can disconnect the phone now
FINISHED [3sec]
 

NANAIU

Well-known Member
Joined
Oct 15, 2010
Age
34
Posts
2,734
Likes
63
Location
BD
answer: Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

4SE - tool 1.8.1
Selected model: Xperia™ X8 (E15)
Selected operation: Flash
Selected interface: USB (EROM)
Checking USB driver status...OK (SEMC Flash Device v2.2.0.5 | 5-4-2010)
Remove battery, wait a few seconds and insert it back
Plug USB cable holding "Back" button
Connected to USB1
You can now release the keys and allow the process to run. Do not disconnect the phone
Device identification...OK
Chip:MSM7227 Model:E15i IMEI:01256000-933385-6 AID:0001 Color:RED
DEVICE_ID: 53659DC89774737C4CA0CD0328C3562753145685
EROM: 1229-3593 R8A029
Uploading logic MSM7227:
Sending LoaderLIVE...OK
Detecting flash type...OK
ID: 2CBC (Micron)
Chip: Micron 4096 Mbit NAND (large page) x16
Logical address: 0x08000000
Size: 528 Mb
OTP: LOCKED
Reading TA security data...OK
E15I 0001 Red (2.1.1.A.0.6 | 1241-4648/R9B) 3 UK/BLACK
Processing 277563214_012DC80C5AE8.SIN_FILE_SET...
Flashing image fota0_S1-SW-LIVE-3EDC-0001-S1-PARTITION.sin...OK
Flashing image fota1_S1-SW-LIVE-3EDC-0001-S1-PARTITION.sin...OK
Flashing image kernel_S1-SW-LIVE-3EDC-0001-S1-PARTITION.sin...OK
Flashing image amss_S1-SW-LIVE-3EDC-0001-S1-PARTITION.sin...OK
Flashing image cache_S1-SW-LIVE-3EDC-0001-S1-PARTITION-WITH-SPARE.sin...OK
Processing 277746985_012E345DADF0.SIN_FILE_SET...
Flashing image amss_fs_shakira_BC18_HUTCH_S1-SW-LIVE-3EDC-0001-S1-PARTITION.sin...OK
Flashing image userdata_S1-SW-LIVE-3EDC-0001-S1-PARTITION-WITH-SPARE.sin...OK
Flashing image system_S1-SW-LIVE-3EDC-0001-S1-PARTITION-WITH-SPARE.sin...OK
Shutting down device...OK
Operation completed successfully. You can disconnect the phone now
FINISHED [123sec]
 

NANAIU

Well-known Member
Joined
Oct 15, 2010
Age
34
Posts
2,734
Likes
63
Location
BD
answer: Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

x10i unlock x10i unlocked with usb cable on software 2.1.


log

SE - tool 1.8.2
Selected model: Xperia™ X10 (X10)
Selected operation: Unlock
Selected interface: USB (EROM)
Checking USB driver status...OK (SEMC Flash Device v2.2.0.5 | 1-29-2010)
Checking ADB drivers status...OK
Remove battery, wait a few seconds and insert it back
Plug USB cable holding "Back" button
Connected to USB2
You can now release the keys and allow the process to run. Do not disconnect the phone
Device identification...OK
Chip:QSD8250 Model:X10i IMEI:35941903-304723-3 AID:0001 Color:RED
DEVICE_ID: B83E644CBDA932AC81AA99C3013E07977C97957F
EROM: 1226-2253 R8A013
Uploading logic QSD8250:
Sending LoaderLIVE...OK
Detecting flash type...OK
ID: 2CB3 (Micron)
Chip: Micron 8192 Mbit NAND (large page) x16
Logical address: 0x08000000
Size: 1056 Mb
OTP: LOCKED
Reading TA security data...OK
Opening TA...OK
Reading SIMLock data...OK
Original HwConf certificate detected
Processing SIMLock signature...OK
Opening TA...OK
Writing SIMLock data...OK
Disconnect USB cable, power on the phone and boot Android OS
Enable USB Debug in Applications menu, make sure ADB drivers installed. Connect USB cable
Starting ADB server...OK
Waiting for CB511HB9WW...OK
Disabling security...OK
Waiting for CB511HB9WW...OK
Installing required module...OK
Writing S1boot image...OK
Rebooting device...OK
Operation completed successfully. You can disconnect the phone now
FINISHED [143sec]
 

NANAIU

Well-known Member
Joined
Oct 15, 2010
Age
34
Posts
2,734
Likes
63
Location
BD
answer: Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

4SE - tool 1.8.2
Selected model: Xperia™ X8 (E15)
Selected operation: Unlock
Selected interface: USB (EROM)
Checking USB driver status...OK (SEMC Flash Device v2.2.0.5 | 5-4-2010)
Checking ADB drivers status...OK
Remove battery, wait a few seconds and insert it back
Plug USB cable holding "Back" button
Connected to USB3
You can now release the keys and allow the process to run. Do not disconnect the phone
Device identification...OK
Chip:MSM7227 Model:E15i IMEI:35678504-012722-3 AID:0001 Color:RED
DEVICE_ID: 86445C8FDFB3D6E39052F50363B0549CE002C3CC
EROM: 1229-3593 R8A029
Uploading logic MSM7227:
Sending LoaderLIVE...OK
Detecting flash type...OK
ID: 20BC (ST)
Chip: ST 4096 Mbit NAND (large page)
Logical address: 0x08000000
Size: 528 Mb
OTP: LOCKED
Reading TA security data...OK
Opening TA...OK
Reading SIMLock data...OK
Original HwConf certificate detected
Processing SIMLock signature...OK
Opening TA...OK
Writing SIMLock data...OK
Disconnect USB cable, power on the phone and boot Android OS
Enable USB Debug in Applications menu, make sure ADB drivers installed. Connect USB cable
Starting ADB server...OK
Waiting for BX902ADTB2...OK
Disabling security...OK
Waiting for BX902ADTB2...OK
Removing NAND restrictions...OK
Waiting for BX902ADTB2...OK
Disabling security...OK
Waiting for BX902ADTB2...OK
Installing required module...OK
Writing S1boot image...OK
Rebooting device...OK
Operation completed successfully. You can disconnect the phone now
FINISHED [117sec]
 

NANAIU

Well-known Member
Joined
Oct 15, 2010
Age
34
Posts
2,734
Likes
63
Location
BD
answer: Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

LT 15 arc unlock successfully
 

NANAIU

Well-known Member
Joined
Oct 15, 2010
Age
34
Posts
2,734
Likes
63
Location
BD
answer: Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

4SE - tool 1.8.2
Selected model: K790
Selected operation: Read info
Selected interface: UART (BOOTROM)
Remove battery, wait a few seconds and insert it back
Connect cable and press "Power" button shortly
Connected to COM8
You can now release the keys and allow the process to run. Do not disconnect the phone
Device identification...OK
Sending Preloader...OK
Starting GDFS service...OK
Reading GDFS security data...OK
Chip
B2020 Model:K790i IMEI:35220601-349505-3 CID:49 Domain:RED
OTP LOCKED:1 CID:49 PAF:1
Uploading logic DB2020:
Firmware details:
Software Id: R1CG001 prgCXC1250477_GENERIC_EV
Software revision: R1CG001
FS Id: cxc1250491
FS version: R1CG001
Language Id: S_ASIA_LEVAN
CDA Id: CDA102568/110
CDA version: R4A
Detecting flash type...OK
ID: 2019 (ST)
Chip: ST Sibley 512 Mbit NOR
Logical address: 0x44000000
Size: 64 Mb
Supported operations:
Flash, Unlock, Recovery, Change certificate, GDFS, Dump flash
Shutting down device...OK
Operation completed successfully. You can disconnect the phone now
FINISHED [9sec]
 

NANAIU

Well-known Member
Joined
Oct 15, 2010
Age
34
Posts
2,734
Likes
63
Location
BD
answer: Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

4SE - tool 1.8.2
Selected model: K790
Selected operation: Unlock
Selected interface: UART (BOOTROM)
Remove battery, wait a few seconds and insert it back
Connect cable and press "Power" button shortly
Connected to COM8
You can now release the keys and allow the process to run. Do not disconnect the phone
Device identification...OK
Sending Preloader...OK
Starting GDFS service...OK
Reading GDFS security data...OK
Chip
B2020 Model:K790i IMEI:35220601-349505-3 CID:49 Domain:RED
OTP LOCKED:1 CID:49 PAF:1
Uploading logic DB2020:
Detecting flash type...OK
ID: 2019 (ST)
Chip: ST Sibley 512 Mbit NOR
Logical address: 0x44000000
Size: 64 Mb
Shutting down device...OK
Remove battery, wait a few seconds and insert it back
Connect cable and press "Power" button shortly
Connected to COM8
You can now release the keys and allow the process to run. Do not disconnect the phone
Device identification...OK
Uploading logic DB2020:
Sending ResetLoader...OK
Authenticating with key KIDP96202033...OK
Reseting to factory defaults...OK
Shutting down device...OK
Remove battery, wait a few seconds and insert it back
Connect cable and press "Power" button shortly
Connected to COM8
You can now release the keys and allow the process to run. Do not disconnect the phone
Device identification...OK
Uploading logic DB2020:
Sending ProductionLoader...OK
Writing EROM...OK
Writing SIMLock data...OK
Changing certificate to A1_DB2020_49_RED...OK
Shutting down device...OK
Operation completed successfully. You can disconnect the phone now
FINISHED [27sec]
 
Top