GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

J

Jonab Ru

Super Moderator
Joined
Feb 3, 2011
Posts
1,838
Likes
6
2 20 10 5 1
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

5130c JASO dead Alive

Initializing...
DA_LIB_VER_3.2.2.7
It is sensing the pinout fast...
D-=8 D+=9
Searching commport...please wait...
Spd USB-to-Serial=COM9
Connecting...
Connected...sending boot...
FDL test...OK
ArmBootMode: 6600700100005A00_01
Wait for init Commzero Security Engine...
Done.
Loading bootloader...
Done.
Changing baudrate...
Set baudrate to 921600 ok
Reading phone HW info...
Read info is done.
CPU: SC6600L2 Flash: NOR_ST_M58WR064KT
setting the Flash Parameters...
Settings have been completed!
Reading FileSystem info...
FileSystem Version: 0A
Start=0x00790000, Size=0x00060000
Unlocking all blocks before program/erase...
Unlock Done.
Auto formatting...
Done.
 
J

Jonab Ru

Super Moderator
Joined
Feb 3, 2011
Posts
1,838
Likes
6
2 20 10 5 1
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

china 5130 spd full flash done china 5130 spd full flash done


Initializing...
DA_LIB_VER_3.2.2.8
It is sensing the pinout fast...
RXD=6 TXD=7
Connecting...
Connected...sending boot...
FDL test...OK
ArmBootMode: 6600700100006A00_01
Wait for init Commzero Security Engine...
Done.
Loading bootloader...
Done.
Changing baudrate...
Set baudrate to 921600 ok
Reading phone HW info...
Read info is done.
CPU: SC6600L2 Flash: NOR_ST_M58WR064KT
setting the Flash Parameters...
Settings have been completed!
Unlocking all blocks before program/erase...
Unlock Done.
Programming...
Compare Image: Enable
All Done.
 
J

Jonab Ru

Super Moderator
Joined
Feb 3, 2011
Posts
1,838
Likes
6
2 20 10 5 1
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

g3 hang on illigal done via reset

Initializing...
DA_LIB_VER_3.2.2.7
It is sensing the pinout fast...
D-=17 D+=19
Searching commport...please wait...
Connecting...
Spd USB-to-Serial=COM6
Connected...sending boot...
FDL test...OK
ArmBootMode: 6600900C2C42A0FF_00
Wait for init Commzero Security Engine...
Done.
Loading bootloader...
Done.
Changing baudrate...
Set baudrate to 115200 ok
Reading phone HW info...
Read info is done.
CPU: SC6600H Flash: NOR_TV00560002EDGB
setting the Flash Parameters...
Settings have been completed!
Unlocking all blocks before program/erase...
Unlock Done.
Analyzing FileSystem...
Done.
Reset the user data area...
Note: if user partition size is more than 4MB, The phone would may take 1 minute to rebuild FileSystem after Reset Action.
All Done.
 
J

Jonab Ru

Super Moderator
Joined
Feb 3, 2011
Posts
1,838
Likes
6
2 20 10 5 1
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

bb lockcode done through rj45 cables


Initializing...
DA_LIB_VER_3.2.2.7
It is sensing the pinout fast...
RXD=6 TXD=2
Connecting...
Connected...sending boot...
FDL test...OK
ArmBootMode: 6600700500006A00_01
Wait for init Commzero Security Engine...
Done.
Loading bootloader...
Done.
Changing baudrate...
Set baudrate to 115200 ok
Reading phone HW info...
Read info is done.
CPU: SC6600L/WT6226 Flash: NOR_ST_M36LOR7050U3ZS
setting the Flash Parameters...
Settings have been completed!
Connect and search Security Code...
Privacy protect: 10275943
PhoneLock: 61820
Done.
 
J

Jonab Ru

Super Moderator
Joined
Feb 3, 2011
Posts
1,838
Likes
6
2 20 10 5 1
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

Boom T20 flash done

Initializing...
DA_LIB_VER_3.2.2.8
It is sensing the pinout fast...
D-=6 D+=5
Searching commport...please wait...
Connecting...
Spd USB-to-Serial=COM11
Connected...sending boot...
FDL test...OK
ArmBootMode: 6600700100005A00_01
Wait for init Commzero Security Engine...
Done.
Loading bootloader...
Done.
Changing baudrate...
Set baudrate to 921600 ok
Reading phone HW info...
Read info is done.
CPU: SC6600L2 Flash: NOR_ST_M58WR064KT
setting the Flash Parameters...
Settings have been completed!
Unlocking all blocks before program/erase...
Unlock Done.
Programming...
Compare Image: Enable
All Done.
 
J

Jonab Ru

Super Moderator
Joined
Feb 3, 2011
Posts
1,838
Likes
6
2 20 10 5 1
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

First time when i format the set format fail & set is dead .......Then i read flash file as same Intex 2060 ....and write to flash the dead set ..... Write full And the set is on problem (all time loud skpr) 100% solve............


Initializing...
DA_LIB_VER_3.2.2.8
It is sensing the pinout fast...
D-=17 D+=19
Searching commport...please wait...
Spd USB-to-Serial=COM15
Connecting...
Connected...sending boot...
FDL test...OK
ArmBootMode: 6600700100005A00_01
Wait for init Commzero Security Engine...
Done.
Loading bootloader...
Done.
Changing baudrate...
Set baudrate to 460800 ok
Reading phone HW info...
Read info is done.
CPU: SC6600L2 Flash: NOR_S29GL064A_T
setting the Flash Parameters...
Settings have been completed!
Unlocking all blocks before program/erase...
Unlock Done.
Programming...
Compare Image: Enable
All Done.
 
J

Jonab Ru

Super Moderator
Joined
Feb 3, 2011
Posts
1,838
Likes
6
2 20 10 5 1
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

Initializing...
DA_LIB_VER_3.2.2.7
It is sensing the pinout fast...
D-=7 D+=10
Searching commport...please wait...
Connecting...
Spd USB-to-Serial=COM9
Connected...sending boot...
FDL test...OK
ArmBootMode: 6600700100005A00_01
Wait for init Commzero Security Engine...
Done.
Loading bootloader...
Done.
Changing baudrate...
Set baudrate to 921600 ok
Reading phone HW info...
Read info is done.
CPU: SC6600L2 Flash: NOR_ST_M58WR064KT
setting the Flash Parameters...
Settings have been completed!
Reading FileSystem info...
FileSystem Version: 0A
Start=0x00790000, Size=0x00060000
Unlocking all blocks before program/erase...
Unlock Done.
Auto formatting...
Done.
 
J

Jonab Ru

Super Moderator
Joined
Feb 3, 2011
Posts
1,838
Likes
6
2 20 10 5 1
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

myphone q3i cant detect on usb but pinout is in headset 100% detected

Initializing...
DA_LIB_VER_3.2.2.7
Tip: The phone must be able to power-on normally
It is sensing the pinout fast,please hold on the phone Power key
RXD=1 TXD=3
Connecting...Please hold on the POWER key until the red gauge is going...
BB:6223, HardwareVer:8A05, SoftwareVer:8A00
Read info...ok, Waitting enter meta...
Connected...can release Power button now, tracking...
Code=1122
Code=64142434
 
J

Jonab Ru

Super Moderator
Joined
Feb 3, 2011
Posts
1,838
Likes
6
2 20 10 5 1
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

e100 format


Initializing...
DA_LIB_VER_3.2.2.7
It is sensing the pinout fast,please hold on the phone Power key
RXD=13 TXD=14
Connecting...Please hold on the POWER key until the red gauge is going...
BB:6225, HardwareVer:8A05, SoftwareVer:8A00
Loading boot...
INT_SYSRAM_BOOT test completed.
Loading boot...
Boot2 test completed.
Nor Flash ID: 0098000300000000
Nand Flash ID: 0000000000000000
Read Hardware Information is done.
Get Project ID from phone...
Project ID: Q8_00A_V5.50
Changing baudrate to 115200...
Done.
Formatting Flash...
AutoFormat address: start=0x00E00000, size=0x00200000
All Done
 
J

Jonab Ru

Super Moderator
Joined
Feb 3, 2011
Posts
1,838
Likes
6
2 20 10 5 1
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

UNLOCK ANA FORMAT CXTEL 790 here are the logs

Initializing...
DA_LIB_VER_3.2.2.8
It is sensing the pinout fast...
RXD=4 TXD=3
Connecting...
Connected...sending boot...
FDL test...OK
ArmBootMode: 6600700100006A00_01
Wait for init Commzero Security Engine...
Done.
Loading bootloader...
Done.
Changing baudrate...
Set baudrate to 921600 ok
Reading phone HW info...
Read info is done.
CPU: SC6600L2 Flash: NOR_ST_M30L0T7000T0
setting the Flash Parameters...
Settings have been completed!
Reading FileSystem info...
FileSystem Version: 0A
Start=0x00DE0000, Size=0x00200000
Unlocking all blocks before program/erase...
Unlock Done.
Auto formatting...
Done.
 
J

Jonab Ru

Super Moderator
Joined
Feb 3, 2011
Posts
1,838
Likes
6
2 20 10 5 1
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

Initializing...
DA_LIB_VER_3.2.2.7
It is sensing the pinout fast...
RXD=6 TXD=2
Connecting...
Connected...sending boot...
FDL test...OK
ArmBootMode: 6600700500006A00_01
Wait for init Commzero Security Engine...
Done.
Loading bootloader...
Done.
Changing baudrate...
Set baudrate to 115200 ok
Reading phone HW info...
Read info is done.
CPU: SC6600L/WT6226 Flash: NOR_ST_M36LOR7050U3ZS
setting the Flash Parameters...
Settings have been completed!
Connect and search Security Code...
Privacy protect: 10265483
PhoneLock: 58746
Done.
 
J

Jonab Ru

Super Moderator
Joined
Feb 3, 2011
Posts
1,838
Likes
6
2 20 10 5 1
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

hello kitty hang done

Initializing...
DA_LIB_VER_3.2.2.7
It is sensing the pinout fast...
D-=23 D+=22
Searching commport...please wait...
Connecting...
Spd USB-to-Serial=COM20
Connected...sending boot...
FDL test...OK
ArmBootMode: 6600700100025A00_01
Wait for init Commzero Security Engine...
Done.
Loading bootloader...
Done.
Changing baudrate...
Set baudrate to 115200 ok
Reading phone HW info...
Read info is done.
CPU: SC6600L2 Flash: NOR_S29GL064A_T
setting the Flash Parameters...
Settings have been completed!
Unlocking all blocks before program/erase...
Unlock Done.
Analyzing FileSystem...
Done.
Reset the user data area...
Note: if user partition size is more than 4MB, The phone would may take 1 minute to rebuild FileSystem after Reset Action.
All Done.
 
J

Jonab Ru

Super Moderator
Joined
Feb 3, 2011
Posts
1,838
Likes
6
2 20 10 5 1
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

Initializing...
DA_LIB_VER_3.3.4.1
It is sensing the pinout fast,please hold on the phone Power key
RXD=6 TXD=7
Connecting...Please hold on the POWER key until the red gauge is going...
Any errors please select another boot and try again.
BB:6226, HardwareVer:8A02, SoftwareVer:8A01
Loading boot...
INT_SYSRAM_BOOT test completed.
Loading boot...
Boot2 test completed.
Nor Flash ID: 002088C400000000
Nand Flash ID: 0000000000000000
Read Hardware Information is done.
Config EMI(Nor Flash only)...
H/W detection ok.
Get Project ID from phone...
Project ID: MAUI.08B.W09.08.MP.V2.0831
Changing baudrate to 921600...
Done.
Formatting Flash...
AutoFormat address: start=0x00E00000, size=0x00200000
All Done
 
J

Jonab Ru

Super Moderator
Joined
Feb 3, 2011
Posts
1,838
Likes
6
2 20 10 5 1
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

here are screenshots.

1.Read info.

2rdyngk.jpg


2. Read full flash

kdk18h.jpg


3.Unlock/read lock codes

15qbzup.jpg


Full flash download from
 
J

Jonab Ru

Super Moderator
Joined
Feb 3, 2011
Posts
1,838
Likes
6
2 20 10 5 1
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

F 800 SUCCESSFULLY FORMATED.

Initializing...
DA_LIB_VER_3.2.2.8
It is sensing the pinout fast...
D-=23 D+=22
Searching commport...please wait...
Connecting...
Spd USB-to-Serial=COM4
Connected...sending boot...
FDL test...OK
ArmBootMode: 6600700500005A00_01
Wait for init Commzero Security Engine...
Done.
Loading bootloader...
Done.
Changing baudrate...
Set baudrate to 921600 ok
Reading phone HW info...
Read info is done.
CPU: SC6600L/WT6226 Flash: NOR_S29GL064A_T
setting the Flash Parameters...
Settings have been completed!
Reading FileSystem info...
FileSystem Version: 0A
Start=0x007B0000, Size=0x00040000
Unlocking all blocks before program/erase...
Unlock Done.
Auto formatting...
Done.
 
You must log in or register to reply here.
Prev Thread | Next Thread
Back
Top