New Solution Repair box JAF without resisters 330 and without remove chip LVC244A
Step 1: You have to find a stem LPT port cable as shown:
Step 2: Open Box JAF and welding as Figure 1 below.
Step 3: View behind JAF BOX. using a scalpel and cut as shown in Figure 3 below.
Step 4: Connect the USB for the JAF Box to use GND and 5V Voltage
Step 5: Download: soft + Firmware of JAF box
Step 7: After installation is complete, we set up as shown below.
The steps to load and select the file you just need to conform to the video is 100% OK. The most important problem is the connection with JAF BOX LPT port only.
http://www.youtube.com/watch?v=uF8HrXt3i1Y
or
download video
RapidShare: 1-CLICK Web hosting - Easy Filehosting
Thanks mr zopo
THE IMAGE ABOVE is 100% TESTED to ME but NOT *quot;DEAD JAF BOX *quot; coz I DON'T HAVE DEAD JAF BOX
but converting
= ATmega8-16AU (32 pins from OTHER BOX WORKING) to USB programmer for Atmel AVR controllers
= ATmega8L-8PI (28 pins from OTHER BOX WORKING) to USB programmer for Atmel AVR controllers
NOW MAKING PCB for this 2 TYPE of Microcontroller to be ABLE TO USE USB NOT PRINTER PORT.
IF I HAVE TIME, I'LL TRY TO CONVERT ATmega128 from OTHER BOX to put it in my OTHER JAF BOX.
Step 1: You have to find a stem LPT port cable as shown:
Just like on the Jack LPT port to attach to the back of the computer.
And on what it has stated that Jack LPT number from 1 to 25 feet (see wealth in'll see). And we only care about 4 feet.
No. 6 feet ..........( called SCK)
No. 7 foot ..............( called Mosi)
No. 9 feet ..............( called reset)
foot No. 10 ............( called miso)
As shown below:
And on what it has stated that Jack LPT number from 1 to 25 feet (see wealth in'll see). And we only care about 4 feet.
No. 6 feet ..........( called SCK)
No. 7 foot ..............( called Mosi)
No. 9 feet ..............( called reset)
foot No. 10 ............( called miso)
As shown below:
Step 2: Open Box JAF and welding as Figure 1 below.
Step 3: View behind JAF BOX. using a scalpel and cut as shown in Figure 3 below.
Step 4: Connect the USB for the JAF Box to use GND and 5V Voltage
Step 5: Download: soft + Firmware of JAF box
Step 7: After installation is complete, we set up as shown below.
The steps to load and select the file you just need to conform to the video is 100% OK. The most important problem is the connection with JAF BOX LPT port only.
http://www.youtube.com/watch?v=uF8HrXt3i1Y
or
download video
RapidShare: 1-CLICK Web hosting - Easy Filehosting
Thanks mr zopo
THE IMAGE ABOVE is 100% TESTED to ME but NOT *quot;DEAD JAF BOX *quot; coz I DON'T HAVE DEAD JAF BOX
but converting
= ATmega8-16AU (32 pins from OTHER BOX WORKING) to USB programmer for Atmel AVR controllers
= ATmega8L-8PI (28 pins from OTHER BOX WORKING) to USB programmer for Atmel AVR controllers
NOW MAKING PCB for this 2 TYPE of Microcontroller to be ABLE TO USE USB NOT PRINTER PORT.
IF I HAVE TIME, I'LL TRY TO CONVERT ATmega128 from OTHER BOX to put it in my OTHER JAF BOX.