GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

Q200 Nokia Formate Done

Initializing...
DA_LIB_VER_3.4.1.2
It is sensing the pinout fast,please hold on the phone Power key
RXD=9 TXD=7
Connecting...Please hold on the POWER key until the red gauge is going...
Any errors please select another boot and try again.
BB:6253, HardwareVer:8A00, SoftwareVer:8A02
Loading boot...
INT_SYSRAM_BOOT test completed.
Loading boot...
Boot2 test completed.
Nor Flash ID: 0001007E00630001
Nand Flash ID: 0000000000000000
Read Hardware Information is done.
Config EMI(Nor Flash only)...
H/W detection ok.
Get Project ID from phone...
Project ID: C100A3.ME.XKT01.110119.01
Changing baudrate to 921600...
Done.
Formatting Flash...
AutoFormat address: start=0x00E00000, size=0x00200000
All Done
 
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

HTTel K78 Formate Done

Initializing...
DA_LIB_VER_3.4.1.2
It is sensing the pinout fast...
D-=3 D+=4
Searching commport...please wait...
Connecting...
Spd USB-to-Serial=COM10
Connected...sending boot...
FDL test...OK
ArmBootMode: 6600700100005A00_01
Wait for init Commzero Security Engine...
Done.
Loading bootloader...
Done.
Changing baudrate...
Set baudrate to 921600 ok
Reading phone HW info...
Read info is done.
CPU: SC6600L2 Flash: NOR_EN71GL064
setting the Flash Parameters...
Settings have been completed!
Reading FileSystem info...
FileSystem Version: 0A
Start=0x00790000, Size=0x00060000
Unlocking all blocks before program/erase...
Unlock Done.
Auto formatting...
Done.
 
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

Club C100 Flash Done
Initializing...
DA_LIB_VER_3.4.1.2
It is sensing the pinout fast,please hold on the phone Power key
RXD=4 TXD=2
Connecting...Please hold on the POWER key until the red gauge is finishing...
Changing baudrate...
Set baudrate to 230400 ok
Reading phone HW info...
Read info is done.
BB: PMB7880 Flash: NOR_S7_SV7E320XT
setting the Flash Parameters...
Settings have been completed!
Unlocking all blocks before program/erase...
Unlock Done.
Programming...
Compare Image: Enable
All Done.
 
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

G9 Nasaki Formate Done

Initializing...
DA_LIB_VER_3.4.1.2
It is sensing the pinout fast,please hold on the phone Power key
RXD=9 TXD=7
Connecting...Please hold on the POWER key until the red gauge is going...
Any errors please select another boot and try again.
BB:6253, HardwareVer:8A00, SoftwareVer:8A04
Loading boot...
INT_SYSRAM_BOOT test completed.
Loading boot...
Boot2 test completed.
Nor Flash ID: 0098009E00000000
Nand Flash ID: 0000000000000000
Read Hardware Information is done.
Config EMI(Nor Flash only)...
H/W detection ok.
Get Project ID from phone...
Project ID: Z100.FET-C5.NASAKI-V3-0525
Changing baudrate to 230400...
Done.
Formatting Flash...
AutoFormat address: start=0x00E00000, size=0x00200000
All Done
 
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

Q Mobile E900 Phone Code

Initializing...
DA_LIB_VER_3.4.1.2
Tip: The phone must be able to power-on normally
It is sensing the pinout fast,please hold on the phone Power key
RXD=2 TXD=3
Connecting...Please hold on the POWER key until the red gauge is going...
Any errors please select another boot and try again.
BB:6235, HardwareVer:8A01, SoftwareVer:8A04
Read info...ok, Waitting enter meta...
Connected...can release Power button now, tracking...
Code=0015
Code=852222
 
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

CCT J5000+ Reset

Initializing...
DA_LIB_VER_3.4.1.2
It is sensing the pinout fast...
D-=8 D+=6
Searching commport...please wait...
Connecting...
Spd USB-to-Serial=COM10
Connected...sending boot...
FDL test...OK
ArmBootMode: 6600700100005A00_01
Wait for init Commzero Security Engine...
Done.
Loading bootloader...
Done.
Changing baudrate...
Set baudrate to 230400 ok
Reading phone HW info...
Read info is done.
CPU: SC6600L2 Flash: NOR_S29GL128N_T
setting the Flash Parameters...
Settings have been completed!
Unlocking all blocks before program/erase...
Unlock Done.
Analyzing FileSystem...
Done.
Reset the user data area...
Note: if user partition size is more than 4MB, The phone would may take 1 minute to rebuild FileSystem after Reset Action.
All Done.
 
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

thanks for sharing brother
 
answer: GPG Dragon Successfully Unlocked / Repaired / Flashed Phones !!!

NOKIA_6252.CPO IME DONE

4uyv6q.jpg




..:::BASHARTEL:::..
 ---@yahoo.com​
 
G.cing 668 tv done with dragon box

G.CING 668 TV MSTAR DONE WITH DRAGON BOX

Read info:.

75194542896752901209.png


Read Flash:.

69113950393349986056.png


Read password:.

35854934774686979169.png


write Flash:.

22106377435855734119.png


Br::.
.::Mustafa::.
 
ccit x1 coolsand 4MB successfully done with Dragon by .::Mustafa::.

ccit x1 coolsand 4MB successfully done with Dragon

Read Info
01.PNG


Read Flash
02.PNG


Read Password
03.PNG


Thanks Dragon Team For Supported coolsand SPU

Br::.
.::Mustafa::.
 
successfully unlock huawei g3621l by gpg dragon

8527huawei_g3621-1.jpg



1.download file
https://drive.google.com/file/d/0B9Yh9kDHyTppTVVEUHBMdmM1S3c/edit?usp=sharing
2.flash with this file
3.formart
all done
>>> USB Pinfind No need Hold Mobile Power key...
>>> Scanning Mobile USB Port...
>>> Detecting COM PortCOM14
Driver Name->>>USB Single Port
Mobile Connection Success...
CPU_ID:MT625A
Hardware Version:CA01
Software Version:0001
>>> Downloading First Boot...
Verifying First Boot...
>>> Downloading Second Boot...
>>> Authenticating BOOT...
BOOT Validation Success...
================NOR Flash Info=================
Flash Size:0x00300000 -> 3M
Flash ID:0x00EF004000160000
Flash Name:SF_W25Q32BV
================NAND Flash Info=================
Flash Size:0x00000000 -> 0M
Flash ID:0x0000000000000000
Flash Name:UNKNOWNUNKNOWN
>>> Switching Baud Rate...
Baud Rate is Switched To:115200
>>> Erasing Flash Now....
>>> Writing Flash File...
All Done...
 
Micromax A26 hang on logo done flash with dragon

Micromax A26 hang on logo done flash with dragon


A26_zpsb1965a90.jpg
 
Samsung GTS5360 Flash Done But Phone startup only samsung logo

Samsung GTS5360 Flash Done But Phone startup only samsung logo


help me
 
You must log in or register to reply here.
Prev Thread | Next Thread
Back
Top