Tips>Problem>Solution> IQ Doctor Box

[New Vision]

ERROR
"SPD USB TO SERIAL NOT FOUND"

Solution:
You need to install the USB drivers for SpreadTrum.
If already install than uninstall it first again install SPD the driver.

 

[New Vision]

answer: Tips>Problem>Solution> IQ Doctor Box

ERROR
Error: Unsaft EFS Address, Please input the right format address and try again.
Failed to auto format.

Solution
Try "Reset" option, If still problem than search 4 a same handset read the flashfile from that working set again write it back to the faulty set.

 

[New Vision]

answer: Tips>Problem>Solution> IQ Doctor Box

ERROR
Nor Flash ID: 0000000000000000
Nand Flash ID: 0000000000000000
Nor Flash not found.

Solution
First try to shake the flash ic at middle heat if still same then replace cpu.

 

[New Vision]

answer: Tips>Problem>Solution> IQ Doctor Box

ERROR
Read info is done.
CPU: SC6600R Flash: NOR_K5L6331CAA
Set FLASH Parameters...
Settings have been completed!
Reading FileSystem info...
Failed to read FS info.

Solution
Flash the set with same file or read flash from a working handset and then flash it to faulty handset.

 

[New Vision]

answer: Tips>Problem>Solution> IQ Doctor Box

ERROR
FAILED TO RUN BOOTLOADER

Solution
Press and hold the * button and keep pressed untill all completed if still same shake the flash ic at middle heat.

 

[New Vision]

answer: Tips>Problem>Solution> IQ Doctor Box

ERROR
FAILED TO RXD

Solution
Select 6600l-USB from mode list

 

[New Vision]

answer: Tips>Problem>Solution> IQ Doctor Box

ERROR

Nor Flash ID: 007F22F600000000
Nand Flash ID: 0000000000000000
Read Hardware Information is
Get Project ID from phone...
ProjectID Not Found

Solution
Change the boot type to 3.952 if still same than shake the CPU at middle heat or change CPU

 

[New Vision]

answer: Tips>Problem>Solution> IQ Doctor Box

ERROR
ERROR: MTK_DA_GET_FAT_INFO_NOT_FOUND

Solution
Try Boot "Ver. 3.1108" from Boot options, if still same than shake the flash ic at middle heat.

 

[New Vision]

answer: Tips>Problem>Solution> IQ Doctor Box

ERROR

Formatting Flash...
AutoFormat address: start=0x00E00000, size=0x00200000
Failed to format Flash...


Solution
Try with different Boots from list if still same then rehot flash chip than CPU

 

[New Vision]

answer: Tips>Problem>Solution> IQ Doctor Box

ERROR

Initializing...
DA_LIB_VER_3.2.0.7
It is sensing the pinout fast...
D-=4 D+=3
Searching commport...please wait...

Solution
Check connection with phone or connect from RX TX points from board if still same than rehot the CPU

 

[New Vision]

answer: Tips>Problem>Solution> IQ Doctor Box

ERROR
NOR FLASH NOT FOUND

Solution
There is NAND flash Plz select NAND from Mode and use Boot 3.1108

 

[New Vision]

answer: Tips>Problem>Solution> IQ Doctor Box

ERROR

Initializing...
DA_LIB_VER_3.2.1.3
It is sensing the pinout fast...
D-=3 D+=0
BOOT set failure, continue to scan...
Sense failure

Solution
Press and hold 0+Power button of your handset until process

 

[New Vision]

answer: Tips>Problem>Solution> IQ Doctor Box

ERROR
Selected collating sequence not supported by the operating system


Solution
You need windows XP DISC

Go to Control Panel > Regional Language> Language> Install East language

 

[New Vision]

answer: Tips>Problem>Solution> IQ Doctor Box

ERROR
"Conjuction Error" while updating your box



SOLUTION
To fix this. you need to upgrade the firmware by using "Emmergency UpGrade" feature.

Disconnect IQ Doctor Box from USB, connect the main cable to IQ Doctor Box.
Now short the "+" and "-" wires of the main cable
Connect computer with USB to IQ Doctor Box.
Open the latest Box firmware Updater software forIQ Doctor Box. Press "ScanPort", Select your IQ Doctor Box comm port number, tick the "Exigency UpGrade" and press "UpGrade-BOX"