GSM PATTOKI

Active Member
Joined
Sep 5, 2010
Posts
345
Likes
8
Each step has a bullet indicating the tool you'll be using. Don't worry about getting lost or confused; hundreds of people have successfully used the Fixit Guide series to repair their laptops.
Tools used in this guide
-Metal Spudger
-Phillips #00 Screwdriver
-Spudger
Parts relevant to this guide
-iPhone 3G Replacement Battery

Step 1 — Battery

Remove the two Phillips #00 screws from the dock-connector end of the iPhone.

6MDaEATCCBdIK3F5.standard


Step 2
There is a fragile rubber gasket between the silver front bezel and black display assembly. Keep your tool as close to the silver front bezel as possible to prevent damaging the gasket.
We recommend a metal spudger for this task, but an X-acto knife should also work, just be careful not to slip.
Insert a metal spudger into the seam between the silver front bezel and the black display assembly on the edge closest to the home button. Gently pry the display assembly up from its bezel.

ZteoudeGgcNUuQaQ.standard


Step 3

If necessary, insert the metal spudger in the same manner on the side of the iPhone and continue to pry up gently. Stop using the metal spudger once the display assembly is up enough that you can lift it up with your fingers.

Step 4

The display assembly is still connected to the iPhone by several cables, so don't try to remove it entirely just yet.

Rotate the display assembly up until it is at an angle of approximately 45 degrees.

1opQfeBnduhXZ3SF.standard


Step 5

Continue to hold the display assembly with one hand, and use your other hand and a spudger to disconnect the black ribbon cable labeled "1."

pwSlolqxhBFFQOej.standard


step 6
Rotate the display assembly up until it is roughly vertical. This will allow easier access for disconnecting the remaining cables.

Use a spudger to disconnect the black ribbon cable labeled "2."

pwSlolqxhBFFQOej.standard


Step 7

Use a spudger to flip up the white plastic tab holding the remaining ribbon cable in place. The white tab will rotate up 90 degrees, releasing the ribbon cable.

Slide the black ribbon cable out of its connector, and remove the display assembly from the iPhone.
QDOLUTpIiNcdCgKb.standard


Step 8

Insert your SIM eject tool or a paper clip into the hole next to the headphone jack.

Press down on the tool until the SIM card tray pops out.

Grasp the SIM card tray and slide it out of the iPhone.

EOIPHToqCfIMHyJM.standard


Step 9

Use a spudger to disconnect the ribbon cable labeled "4."

rGWSGdsIfraEEGDF.standard



Step 10

Use a spudger to disconnect the ribbon cable labeled "5."

BQMTNLaEuoTM1dbP.standard


Step 11

Use a spudger to disconnect the ribbon cable labeled "6."

jZ6cQMUHCQjSQYch.standard


Step 12

Carefully peel up the small sticker labeled "Do not remove."

VadTQEnZGGD53CuS.standard


Step 13

Remove the following 8 screws:

Five 2.3 mm Phillips #00 screws with partial threads securing the logic board to the rear panel.

Two 2.3 mm Phillips #00 screws with full threads securing the logic board and camera.

One 2.9 mm Phillips #00 screw from beneath the "Do not remove" sticker.

2qikdfJo3tebRKuE.standard


Step 14

Use a spudger to gently pry the camera up and out of its housing in the rear panel. The camera cannot be removed entirely yet because it's connected to the bottom of the logic board.

FctBMcDEDkIIEtJt.standard


Step 15

Use a spudger to gently pry up the end of the logic board closest to the dock connector.

If the board won't lift up, double check to make sure all the screws securing the logic board have been removed.

NMdOyCP4DiDuVULx.standard


Step 16

Slide the logic board towards the dock connector and out of the iPhone.
h4yEmmTrpKcHXvSB.standard


Step 17

Use a spudger to pry the battery up from the rear panel. The battery is attached with an adhesive strip around the perimeter of the battery. To prevent the battery from bending during the removal process, we recommend against using just the plastic

CtlO6qZ3oNR3gjDx.standard
 
Back
Top