good morning to all,
i wana share this asha 200 problem blingking only first i did flash high version and same product code but no luck thin i diside to open it and reheat...
reheat this part thin flash again it works 1000%
heres the logs...
done
Good bless to all
i wana share this asha 200 problem blingking only first i did flash high version and same product code but no luck thin i diside to open it and reheat...
reheat this part thin flash again it works 1000%
heres the logs...
Code:
MXKEY [MxKey Team HTI Flasher Interface (WinUSB) 3], SN: C08604C5
Using device: USB ROM and HTI, FW ver: 00.50, SN: 0000687A
Connection status: UHCI:HUB::USB 1.10 (Full-speed)
Driver: nmwcdnsuc, ver: 7.1.32.75
Module ver: 1.0.0.20814(05-05-2012), Library ver: 1.0.0.14060(05-05-2012)
Make sure USB cable, Battery and charger are removed from device.
Insert USB cable, Battery back to device(make sure to have fully charged battery).
Insert Charger or Press phone's power button(if flashing doesnt start automatically)
Waiting for USB ROM device ...
Make sure USB cable, Battery and charger are removed from device.
Insert USB cable, Battery back to device(make sure to have fully charged battery).
Insert Charger or Press phone's power button(if flashing doesnt start automatically)
Waiting for USB ROM device ...
Device synchronized.
CPU: XGOLD 213
Sending EBL Loader...OK
Sending EBL ...OK
Getting EBL Version ...
Boot mode: 0xCC
EBL version major/minor: 10.37
EBL version: Quantum_Bootloader_10.37_M1S1
Protocol version suggested by phone: 3
Set baud rate to: 6.50 Mbit/s
Flash ID: 0089 8982 - 23280001 [Intel NU48F512,512 Mbits]
CFI information:
Flash settings: 0/1024, size: 0x04000000
1 Block regions:
512 x 0x00020000 = 0x04000000
EBL ready !
Original IMEI:
RPL backup already exist (C:\mobileEx\3.5\data\backup\XGOLD__back.RPL)
Processing file: rm761__10.60.mcusw
Downloading item CODE:rm761__10.60.mcusw_ebl_psi.fls, num block: 4, size: 25.25 MB
Erasing area 0x40000000-0x4001FFFE ...OK
Programming completed in 2.860 s
Erasing area 0x40040000-0x4005FFFE ...OK
Programming completed in 0.485 s
Erasing area 0x40060000-0x4015FFFE ...OK
Programming completed in 1.953 s
Erasing area 0x40280000-0x41A7FFFE ...OK
Programming completed in 45.781 s
Checksum verified (0xA72F)
Processing file: rm761__10.60.ppm_t
Downloading item CUST:package_t.ppm_ebl_psi.fls, num block: 1, size: 6.05 MB
Erasing area 0x41A80000-0x4208BF42 ...OK
Programming completed in 11.094 s
Checksum verified (0xA5E3)
Processing file: rm761__10.60.image_t_059K955_002
Downloading item CUST:package_t_059K955.image.fls, num block: 1, size: 13.63 MB
Erasing area 0x421C0000-0x43E1FFFE ...OK
Programming completed in 27.250 s
Checksum verified (0x6859)
Total time for flashing process(boot+erase+write) was 13 min 58.235 s
Waiting for USB device removal ...
Waiting for device boot up ...
Device connected: nmwcdc\Nokia USB Phonet, PORT_ID: 3210E3A7
Verifying communication to device OK.
Phone type: RM-761 (Nokia 2000)
SW version: V 10.60 20-01-12 RM-761 (c) Nokia
Imei plain: 35825904573126-2
Product code: 059K955
Language Pack:
- not available.
SLPA ver[4]: PA_SL3/PA_SIMLOC30 (15 digit NCK)
warning: avoid SW Downgrade & manual erase to this phone !
Camera config: 06150123005023, ver:
SIMLOCK seems to be valid
SUPERDONGLE_KEY invalid!
- WD timer enabled, phone will reboot itself after 3 min.
SIMLOCK_TEST passed
SECURITY_TEST passed
Imei net: 35825904573126
Version: SIMLOCK SERVER
Provider: GSM Test Operator
Counter: 0/3, 0/10
CONFIG_DATA: 0010100000000000
PROFILE_BITS: 800000000003000B
BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
FULL FACTORY... OK
Completed in 0.047 sdone
Good bless to all